PH_PC-Stations_76.pdf

(13074 KB) Pobierz
Commissioning PC Stations - Manual
and Quick Start
___________________
Preface
Welcome to Advanced PC
1
___________________
Configuration
SIMATIC NET
Industrial Communication
Commissioning PC Stations -
Manual and Quick Start
Configuration Manual
2
___________________
Getting started
3
___________________
Examples
4
___________________
Tools
A
___________________
FAQs
B
___________________
References and literature
Release 06/2011
C79000-G8976-C156-14
Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the relevant information is not taken into account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C156-14
Ⓟ 06/2011
Copyright © Siemens AG 2010,
2011.
Technical data subject to change
Preface
This manual…
… supports you when commissioning your SIMATIC NET PC modules in a PC station and
helps you to use them successfully.
… introduces all the tools made available by the SIMATIC NET software for solving your
communication tasks.
… along with the OPC documentation on the SIMATIC NET PC / Windows CD answers your
questions on all aspects of communication:
Note
Variants in the descriptions
The activities described in this manual depend on the operating system you are using.
For Windows 7 and Windows Server 2008 R2, the default display setting is used.
Commissioning PC Stations - Manual and Quick Start
Configuration Manual, Release 06/2011, C79000-G8976-C156-14
3
Preface
New in this release
● Description of the OPC Scout V10.
● Description of the Symbol Editor.
● Description of the new configuration tool "STEP 7 Professional V11".
Documents on the Internet
You can obtain numerous documents from the Internet.
You will find the current version of this manual on the Internet.
Link to the manual: (http://support.automation.siemens.com/WW/view/de/13542666)
Additional information on SIMATIC S7 and STEP 7
The documentation on SIMATIC S7 and STEP 7 contains additional information on the
STEP 7 basic software of the SIMATIC automation system. You can obtain this from your
local Siemens office.
Validity of this manual
The information in this manual applies to the following:
● Version 5.3 SP1 and higher of the project engineering software SIMATIC NCM PC /
STEP 7 with the NCM S7 option
● "SIMATIC NET, PC Software, Edition 2008" CD and higher
References /.../
References to other manuals and documentation are indicated by numbers in slashes /.../.
These numbers refer to the titles of manuals listed in the References section at the end of
the manual.
Commissioning PC Stations - Manual and Quick Start
4
Configuration Manual, Release 06/2011, C79000-G8976-C156-14
Contents
Preface ...................................................................................................................................................... 3
1
Welcome to Advanced PC Configuration................................................................................................. 11
1.1
1.2
1.3
1.4
1.4.1
1.4.2
1.4.3
2
2.1
2.1.1
2.1.2
2.1.2.1
2.1.2.2
2.1.2.3
2.2
2.2.1
2.2.2
2.3
2.3.1
2.3.2
2.3.2.1
2.3.3
2.3.3.1
2.3.3.2
2.3.3.3
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.4.5.1
2.4.5.2
2.5
2.5.1
2.5.2
2.5.2.1
2.5.2.2
A concept for your benefit ............................................................................................................11
PC stations in SIMATIC ...............................................................................................................13
A brief introduction to tools and utilities .......................................................................................16
Guide to installation and commissioning .....................................................................................17
PG mode or configured mode - Considerations ..........................................................................17
Commissioning for PG mode - Overview.....................................................................................19
Commissioning for configured mode - Overview .........................................................................20
"Configured mode".......................................................................................................................23
Steps in project engineering ........................................................................................................24
Steps for initial configuration........................................................................................................29
Case a) Initial configuration using remote configuration with STEP 7 / NCM PC .......................30
Case b) Initial configuration with XDB file....................................................................................34
Case c) Initial configuration using the Station Configuration Editor.............................................37
"PG mode" ...................................................................................................................................39
Configuration for PG mode - programming device (PG/PC) .......................................................40
Configuration for PG mode - HMI stations...................................................................................43
Using additional functions - points to note ...................................................................................47
Checking the configuration and diagnostics ................................................................................47
Testing with OPC Scout V10 .......................................................................................................47
Detecting errors in communication with the OPC Scout V10 ......................................................48
Further functions / special features..............................................................................................49
Adopting the project engineering and symbols from PROFINET iMap and SIMOTION
Scout ............................................................................................................................................49
Configuring access points for STEP 7 and STEP 5.....................................................................51
Points to note with SOFTNET Industrial Ethernet modules.........................................................52
Configuring the OPC server.........................................................................................................53
Significance of project engineering..............................................................................................54
Configuring the properties of the OPC server..............................................................................55
Specifying connection properties for the OPC server in project engineering ..............................57
Using symbols for S7 connections...............................................................................................61
Configuring OPC properties for SNMP in project engineering ....................................................62
Significance in SIMATIC NET ......................................................................................................62
SNMP traps..................................................................................................................................63
Using the CP 1616 as a PROFINET IO controller / IO device / IO router ...................................64
Initialize CP 1616 (IP address and device name)........................................................................66
Configuring the CP 1616..............................................................................................................67
Using the CP 1616 as a PROFINET IO controller .......................................................................67
Using the CP 1616 as a PROFINET IO device ...........................................................................69
Getting started ......................................................................................................................................... 23
Commissioning PC Stations - Manual and Quick Start
Configuration Manual, Release 06/2011, C79000-G8976-C156-14
5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin