taitprograming.pdf

(407 KB) Pobierz
RADIO PROGRAMMING
Conventional Radios:
In the “Key Settings”
window, set the “Key Operation” as latching.
TVS-2-TAIT-T2
Manual Revision: 04-04-01
Covers Software Revisions:
TVS-2-TAIT-T2:
4.6
This manual & product supports the following radios:
Tait T-201X/2020/203X/2040
SPECIFICATIONS
Operating Voltage
Operating Current
Operating Temperature
Frequency Response
Input Impedance
Carrier Suppression
Audio Output Impedance
Encryption Sequences
Random Number Generator
Sequence Length (est.)
5 VDC
8 mA
-30 - +60 C
300-2600 Hz
>100 kΩ
60 dB < Peak Voice
1K
Ω
1 Trillion
64 bits
84 billion years
Trunked Radios:
In the “Specifications” window,
check the “Scrambler” box under “Installed Options”.
INSTALLATION OVERVIEW
1. Test the radio for functionality.
2. Program the radio per the Radio Programming
Section of this manual.
3. Install the scrambler into the radio per the
Hardware Installation Section of this manual.
4. Program the scrambler per the Product
Programming Section of this manual.
***Midian is not responsible for any damage/loss
resulting from the use of Midian’s products.
HARDWARE INSTALLATION
Be certain to follow standard anti-static procedures
when handling any of Midian’s products.
Disassembling the Radio:
Additional disassembly instructions
available in Tait’s Service Manual.
are
also
1. Power should not be connected to the radio.
ABOUT THE TVS-2-TAIT-T2
The TVS-2-TAIT-T2 is a high-level rolling code
scrambler that uses hopping type rolling code
encryption for higher security rather than sweeping
code type. The scrambler is capable of features
such as ANI, ENI, Deadbeat Disable, Spy, and more
when using Midian’s Kryptic Signaling format with
the CAD-300 or DDU-300.
1
2. Remove the top cover by unscrewing the four
screws located on the bottom of the radio.
3. Remove the 3 screws that hold the logic PCB in
place.
4. The logic PCB should flip to the right, when the
radio face is to the front.
Installing the Scrambler:
Conventional Radios:
Plug the scrambler onto the
options connecter labeled P2 (see diagram below).
PRODUCT PROGRAMMING
Midian’s TVS-2-TAIT-T2 series products are
programmed via Midian’s KL-3 programming cable.
Please reference the KL-3 manual for setup
instructions of the KL-3 software and hardware.
From the product selection screen on the KL-3 UP
software, select the TVS-2-TAIT-T2 from the list and
click OK.
Set the parameters of the TVS-2-TAIT-T2 software
to fit the application. If any clarifications on a feature
are required, move the mouse cursor over the
feature name until the question mark appears and
right click, a definition of the feature will be shown.
After entering the parameters, save the file by going
to File - Save As. Enter the file name in the File
Name block and click Save. Saving the file will allow
for quick and easy reprogramming of units.
KL-3 Programming:
After plugging the board into
the radio, but with the radio still open (see
installation section), connect the black lead of the
KL-3 to a common ground and the green clip lead to
the Program In hole. Turn power on to the radio and
click “Program Unit” in the KL-3 software. You will
hear 3 beeps if programmed successfully (see Alert
Tone under Installing the Scrambler).
Trunked Radios:
Plug the scrambler on the options
connector labeled T3K45 (see diagram below).
Alert Tone:
This is needed for Go-Ahead Beeps,
programming beeps, and ring tones. Run a jumper
wire from the ATP hole on the TVS-2-TAIT-T2 to
#S13 Pin 9 on the radio.
PTT Out:
For features such as trailing ANI,
transpond, Emergency ANI, Deadbeat Disable, Spy,
etc. it will be necessary to run a wire from the PTT
Out hole on the TVS-2-TAIT-T2 to S10 Pin 3 located
at the MIC Jack on the radio.
Prog Out
Prog In
Reassembling the Radio:
At this point, programming must be done. Stop here
and skip to the programming section.
Additional assembly instructions are also available in
Tait’s Service Manual.
1. Reinstall the logic PCB with the 3 screws.
2. Reinstall the top cover with the 4 screws.
KL-3 Reading:
It will be necessary to connect the
yellow clip lead to the Program Out hole, in addition
to having the green clip lead connected to the
Program In hole. Follow the same procedure to
read the unit as for programming, but select “Read
Unit” in the menu bar. It is necessary to cycle power
after programming or reading.
Note:
When the
scrambler is read, the security codes will be read out
as zeroes. If another scrambler is then cloned with
this information, the scramblers will be incompatible
because they have different security codes.
HARDWARE ALIGNMENT
The TVS-2-TAIT-T2 does not require any hardware
adjustments, however, when ordering the scrambler,
the radio it will be used in must be specified.
2
OPERATION
Conventional Radios:
The auxiliary button is used
as the scramble/clear (mode) select on this radio.
The auxiliary button is the button with the bell figure
on it. Please note that the button is latched, so only
single code operation is available.
Trunked Radios:
The function button is used as
the scramble/clear (mode) select on this radio. The
function button is the button with “Fn” on it. Please
note that the button is latched, so only single code
operation is available.
TECHNICAL NOTES
Radio Compatibility:
Midian has taken the utmost
care to ensure the option board integrates into the
radio with minimal impact to the features of the
radio. However, some features may not be available
in the radio when an option board is used. If a
feature is not available, please contact Midian to see
if the feature can be added.
DTMF Dialing:
DTMF Dialing may only be
accomplished from the microphone when in clear
mode.
MIDIAN CONTACT INFORMATION
Midian Electronics Inc.
nd
2302 East 22 Street
Tucson, Arizona 85713 USA
Orders: 1-800-MIDIANS
Phone: 520-884-7981
Fax: 520-884-0422
E-mail:
sales@midians.com
Web:
http://www.midians.com/
3
-
This page intentionally left blank
-

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin