Haldex DTC Guide.pdf

(16 KB) Pobierz
DTC
Description
Possible Cause
P056017
P060254
System Voltage
Powertrain Control
Module Programming
Error
Circuit voltage above threshold
Action
Carry out the pinpoint tests
associated to this DTC using the
manufacturer approved
diagnostic system
Re-program using IDS. If still
failed, replace Haldex ECU
Failure during programming.
Install a new Haldex ECU as
required, refer to the new
module/component installation
note at the top of the DTC Index.
P060749
Control Module
Performance
Module internal electronic
component failure
P074812
Pressure Control
Solenoid A Electrical
Pressure Control Valve Short
Circuit to Battery
Check Valve connection first and
install a new Haldex ECU if
required, refer to the new
module/component installation
note at the top of the DTC Index.
P074814
Pressure Control
Solenoid A Electrical
Pressure Control Valve Short
Circuit to Ground or Open Circuit
Check Valve connection first and
install a new Haldex ECU if
required, refer to the new
module/component installation
note at the top of the DTC Index.
P093211
Hydraulic Pressure
Sensor Circuit
Check Pressure/Temperature
Sensor connection and replace
first. If fault still exists, install a
new Haldex ECU as required,
refer to the new
module/component installation
Pressure Sensor Short Circuit to note at the top of the DTC Index.
Ground.
Check Pressure/Temperature
Sensor connection and replace
first. If fault still exists, install a
new Haldex ECU as required,
refer to the new
module/component installation
Pressure Sensor Short Circuit to note at the top of the DTC Index.
Battery
Check Pressure/Temperature
Sensor connection and replace
first. If fault still exists, install a
new Haldex ECU as required,
refer to the new
module/component installation
Temperature Sensor Short Circuit note at the top of the DTC Index.
to Ground
P093215
Hydraulic Pressure
Sensor Circuit
P093711
Hydraulic Oil
Temperature Sensor
Circuit
P093715
Hydraulic Oil
Temperature Sensor
Circuit
Check Pressure/Temperature
Sensor connection and replace
first. If fault still exists, install a
new Haldex ECU as required,
refer to the new
module/component installation
Temperature Sensor Short Circuit note at the top of the DTC Index.
to Battery
Install a new Haldex ECU as
required, refer to the new
module/component installation
note at the top of the DTC Index.
Module internal failure
Install a new module as
required, refer to the new
module/component installation
note at the top of the DTC Index.
Check wiring to Pump and
replace pump if found faulty, if
no fault with Pump, replace
Module only.
Pump Short Circuit to Battery.
Check wiring to Pump and
replace pump if found faulty, if
no fault with Pump, replace
Module only.
Pump Short Circuit to Ground.
Check Pump and sensor
Coupling has failed to reach base performance using diagnostics
pressure within the time allowed. to check pressure reading.
Issue could be pressure sensor Replace sensor first, then check
oil level. Finally, replace pump.
failure (reading too low), pump
failure or low oil.
Temperature above 110Deg C or No action, EVENT DTC only.
below -40Deg C.
Carry out the pinpoint tests
associated to this DTC using the
manufacturer approved
Bus Off
diagnostic system
Carry out the pinpoint tests
associated to this DTC using the
One or more CAN frames
manufacturer approved
missing from the EMS
diagnostic system
Carry out the pinpoint tests
associated to this DTC using the
One or more CAN frames
manufacturer approved
missing from the ABS
diagnostic system
Carry out CAN network integrity
tests using manufacturer
approved diagnostic system
P093827
Hydraulic Oil
Temperature Sensor
Range/Performance
P096162
Pressure Control
Solenoid A Control
Circuit
Range/Performance
Mechanically Stuck Valve (CMS
Error)
P188912
Oil Pressure Pump
Performance
P188914
Oil Pressure Pump
Performance
P188974
P188A68
Oil Pressure Pump
Performance
Differential Oil
Temperature Too
U000100
High Speed CAN
Communication Bus
U010000
U012100
Lost Communication
With ECM/PCM "A"
Lost Communication
With Anti-Lock Brake
System (ABS) Control
Module
U013800
Lost Communication
with All Terrain Control One or more CAN frames
Module
missing from the ATCM
U014000
Lost Communication
With Body Control
Module
One or more CAN frames
missing from the BCM
Carry out the pinpoint tests
associated to this DTC using the
manufacturer approved
diagnostic system
U030000
Re-configure the CJB using the
manufacturer approved
diagnostic system. Clear the
DTC and retest. If the DTC is
still logged suspect the active on-
demand coupling module, refer
Invalid configuration message is to the new module/component
Internal Control Module received from CEM fror vehicle or installation note at the top of the
Software Incompatibility not received at all.
DTC Index
Internal Control Module Incorrect component installed
Software Incompatibility internally.
U03004A
Install correct component
U040168
Invalid Data Received
From ECM/PCM
Invalid Data Received
From Brake System
Control Module
Control Module
Configuration
Incompatible
Vehicle Identification
Number
Invalid data received
Check ECM for DTCs and refer
to the relevant DTC Index.
Check ABS module for DTCs
and refer to the relevant DTC
Index.
U041868
Invalid data received
Check/amend Car Configuration
File using manufacturer
approved diagnostic system
Ensure correct module Haldex
ECU installed
Carry out the pinpoint tests
associated to this DTC using the
manufacturer approved
diagnostic system
U210100
Car Configuration File data
parameter incorrect
Incorrect VIN detected - incorrect
module installed to vehicle
Mis-match in battery voltage,
between CJB and Active On-
demand Coupling module, of 2
volts or more
U300281
U300362
Battery Voltage

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin