Auta Przed Liftingiem ================== 1. Włączenie Testu Zegarów[ Powoduje podczas uruchamiania silnika automatyczne wychylenie wskazówek przez cały zakres prędkościomierza i obrotomierza . [Select] [17 - Instruments] [Coding - 07] [Long Coding Helper] Kliknij na bajt 1, a zobaczysz opcję wyboru: "Gauge Test/Needle Sweep active" Zaznacz tę opcję [Do It!] 2. Włączenie Lap Timer'a [Select] [17 - Instruments] [Coding - 07] [Long Coding Helper] Kliknij na bajt 1, a zobaczysz opcję wyboru: "Lap Timer active" Zaznacz tę opcję [Do It!] 3. Doświetlenie Krawężników Illuminating the kerb when turning hard left or right at low speeds with dipped beam on, by turning on the all-weather light on the relevant side of the car. [Select] [09-Cent. Elect.] [Coding - 07] [Long Coding Helper] Click on byte 4 and enable bit 0 [Do It!] 4. Sygnał Zamknięcia Zamka Syrena alarmowa krótko zaćwierka, gdy alarm zostanie uaktywniony (tzn. Wszystkie drzwi są zamknięte, a samochód jest zablokowany) [Select] [46-Central Conv.] [Coding - 07] [Long Coding Helper] Click on byte 1 and in bit 2 you'll see the selectable option: "Anti-Theft-System: Horn Confirmation active" Check this option [Do It!] 5. Ukryte Zielone Menu Enable access to the green engineering menu in the MMI [Select] [5F - Information Electr.] [Adaptation - 10] Select Channel 6 and Read change the value from 0 to 1 then Test then Save Reboot the MMI (Press MENU, central MMI knob and top right softkey) To get to the Hidden Menu, press and hold the CAR and MENU buttons for a few seconds. You may have to have a few attempts - if you don't press them at the exact same moment either CAR or MENU activates. You know if you have done it right because the red LEDs in the buttons do not illuminate. WARNING!!!! BE CAREFUL!!! Do not mess with settings in the Hidden Menu unless you know what you are doing. On earlier MMI versions, people managed to activate the bootloader menu and fried their MMI. Use at your own risk. If in doubt, leave well alone! 6. Wkaźnik Baterii Enter the Hidden Menu as in step 5 above. Select Car Select Carextdevicelist Check "Battery" Return Select Carmenuoperation Set "Battery" from 0 to 5 Return Press CAR to exit the hidden menu Reboot the MMI Despite doing this, I could not find the battery meter displayed anywhere. I am a muppet though - it may be lurking in a menu I haven't found yet 7. Aktywacja Video In Motion Video In Motion - prevent the car from suppressing DVD playback once the speed of the car rises above 5mph I used the same technique as in my C6 with MMI 3G. These are the steps I followed: [Select] [5F-Information Electr.] [Advanced ID - 1A] Make a note of the Serial Number Go to Enable VIM TV-playback using VCDS/VAG-COM in your Audi MMI | trick77.com Follow the link for MMI 3G Enter your serial number into the input field Make a note of the personal login code and the alternative login code it returns [Security Access - 16] Enter your personal login code. [Do it!] If you receive a "code not valid" message try the alternative code. If neither code works it's likely that your control module doesn't support VIM adaptation. [Adaptation - 10] Select channel 48 Press read Set the value from 0 to 255 Press test Press save Press "Done, Go Back" Close VCDS and reboot your MMI as detailed in step 5 above This works as expected. 8. Aktywacja opuszczania prawego lusterka przy jeździe wstecz When reverse gear is selected, the passenger door mirror dips to show the kerb if the mirror control knob is set to the passenger door mirror position. When driving forwards and exceeding 5mph or when switching off the car, the passenger mirror returns to its original position. If the position of the mirror is changed when dipped, this change is remembered the next time the mirror dips. [Select] [52 - Door Elect, Pass] [Coding - 07] [Long Coding Helper] Click on Byte 4 (5th one along from the left) Set Bit 2 to "on" [Do It!] Full details of this mod are lower down in the thread - it is a little disconcerting at the moment because VCDS has no information for the module and displays a warning when selecting Long Coding Helper. This works as expected 9. Wyłączenie sygnału ostrzeżenia niezapiętych pasów bezpieczeństwa Turn off the annoying "Bing bong" when you move the car on the driveway without your seatbelt fastened. [Select] [17 - Instruments] [Coding - 07] [Long Coding Helper] Click on byte 0 and in bit 4 you'll see the selectable option: "Seat Belt Warning inactive" Check this option [Do It!] 10. Wyłączenie zatrzymania silnika po otwarciu drzwi kierowcy Recode the Central Convenience module to STOP the engine from turning off when you get out, having moved the car. [Select] [46 - Central Conv.] [Coding - 07] [Long Coding Helper] Click on the red byte (below) and in the binary code you will see: 00000111 Change it to: 00001111 ie. with 1111 at the end not 111 Tab into the next bit box and you will see the code change to 0F (013F062220B9000083200904200104070000000000000000000000000000 to 013B062220B90000832009042001040F0000000000000000000000000000) [close the long code helper] [Do It!] Thanks to Mr Fish for finding and posting this up. 11. Włączenie ustawienia domyślnej odległości w MMI Adaptive Cruise Control Adding the option to modify the default distance for ACC (values 1 to 4) via the MMI [Select] [13 - Auto Distance Regulation] [Adaptation - 10] Select channel 07 Press read Set the value from 0 to 1 Press test Press save Press "Done, Go Back" Close VCDS and reboot your MMI as detailed in step 5 above In the MMI you should now be able to go to Car > Driver Assistance > Adaptive Cruise and see a new option there to set the adaptive cruise distance. 12. Próg prędkości dla High Beam Assist Changing the threshold speed at which High Beam Assist activates [Select] [20 - High Beam Assist] [Adaptation - 10] From the drop-down menu, select "High Beam Speed Threshold" In the third entry box down on the left, enter the speed to set the threshold to in KM/h (eg 40) Press save Press "Done, Go Back" Close VCDS and reboot your MMI as detailed in step 5 above 13. Włączanie / Wyłączanie świateł dziennych w MMI Adding the option to turn off / turn on the DRLs via the MMI [Select] [09-Cent. Elect.] [Coding - 07] [Long Coding Helper] Click on byte 3 and enable bit 0 (Daytime running lights adjustable via MMI) [Do It!] 14. Opcja Trybu podróży dla reflektorów w MMI [Select] [09-Cent. Elect.] [Coding - 07] [Long Coding Helper] Click on byte 4 and enable bit 6 [Do It!] Thanks to diecastsink for finding and posting this up. 15. Włączanie automatycznego hamulca postojowego, po przełożeniu dźwigni w pozycję P [Select] [53 - Parking Brake] [Security Access - 16] Code displayed to me was - 78713 [Adaption - 10] Wybierz z menu rozwijanego IDE07959 – Automatic parking brake for selector level position P Zmień parametr Set to Activated [Do It!] Uwaga: Hamulec złącza się dopiero po wyłączeniu silnika 16. Elektryczna klapa bagażnika, zamykanie z kluczyka [Select] [46 - Cent Conv] [Coding - 07] Click on byte 2, bit 2 Tick Comfort operation: Remote control active [Do It!] [Select] [4D - Trunk Elec] [Security Access - 16] Input 12345 [Adaption - 10] Activation using rear lid opening button in remote key - Touch function for closing Change to ACTIVE [Do It!] 16b. Elektryczna klapa bagażnika, zamykanie z kluczyka i przycisku w drzwiach - Facelift models [Select] [46 - Cent Conv] [Coding - 07] [Long Coding Helper] Byte 2, bit 2 "Comfort operation: Remote control active" should be checked, so no need to change it, just confirm that it's set. No Change, Original Coding: Bit 2 checked [Select] [6D - Trunk Elec] [Security Access - 16] Input 12345 [Adaption - 10] There are 8 options for "Activation using rear lid. . .". Change the two "number 4" settings to active. Original Coding: (1)-Activation using rear lid opening button in remote key - Touch function for opening: not active (2)-Activation using rear lid opening button in remote key - Tap function for opening: active (3)-Activation using rear lid opening button in remote key - Touch function for closing: active (4)-Activation using rear lid opening button in remote key - Tap function for closing: not active (1)-Activation using rear lid remote unlocking switch - Touch function for opening: not active (2)-Activation using rear lid remote unlocking switch - Tap function for opening: active (3)-Activation using rear lid remote unlocking switch - Touch function for closing: active (4)-Activation using rear lid remote unlocking switch - Tap function for closing: not active New Coding: (1)-Activation using rear lid opening button in remote key - Touch function for opening: not active (2)-Activation using rear lid opening button in remote key - Tap function for opening: active (3)-Activation using rear lid opening button in remote key - Touch function for closing: active (4)-Activation using rear lid opening button in remote key - Tap function for closing: active (1)-Activation using rear lid remote unlocking switch - Touch function for opening: not active (2)-Activation using rear lid remote unlocking switch - Tap function for opening: active (3)-Activation using rear lid remote unlocking switch - Touch function for closing: active (4)-Activation using rear lid remote unlocking switch - Tap function for closing: active Changing the first "number 4" allows closing of the trunk lid with a quick press of the trunk button on the remote control. Changing the second "number 4" allows closing of the truck lid with a quick pull of the trunk switch (in the driver's side door) The trunk is still opened as before. It will beep when remote closing. 17. Włączenie podwójnego sygnału przy rozbrojeniu [Select] [46 - Central Conv.] [Adaption - 10] Kanał 63 Dodaj 4 [Do It!] 18. Wyłączenie ściemniania DRL przy włączonym kierunku [Select] [09 - Central Elec.] [Security Access - 16] Kod: 20113 [Adaption - 10] Kanał 3 Ustaw wartość od 5 do 100 [Do It!] (Uważam, że 50 to dobra wartość) 19. Zwalnianie hamulca postojowego bez zapiętych pasów [Select] [53 - Parking Brake] [Security Access - 16] Code presented by program [Adaption - 10] Wybierz z menu rozwijanego Zmień parametr ENG101131 – Seat belt buckle detection [Do It!] 20. Włączenie tylnych świateł z DRL [Select] [09-Cent. Elect.] [Coding - 07] [Long Coding Helper] Kliknij na bajt 2, zanacz bit 7 [Do It!] 21.Włączenie zgrywania CD na MMI HDD Wejdź w ukryte menu, wykonaj 5 kroków jak poniżej. Select Main Select Diagnose Select Settings Select Import_Multimedia Check "Ripping" Return Naciśnij CAR, aby wyjść z ukrytego menu Zrestartuj MMI 22. Enable "Make calls using" feature in cars before MY2013 that have been updated to MMI 0770 Enter the Hidden Menu as in step 5 above. Select Main Select Diagnose Select Settings Select tel_settings Check "NAD operation mode" Return Press CAR to exit the hidden menu Reboot the MMI After the reboot you will be prompted with the option to choose which device to use to make calls. Once you've selected which phone to use to make calls (mmi or mobile telephone) the system will advise a reboot is required which it will do itself. 23. Adjust brightness of DRLs when headlights are on [Select] [09-Cent. Elect.] [Security Access - 16] (enter security code - 20113) [Adaptation - 10] Select Channel 03 and Read Change the value from 5 to 100 Press Test then press Save 24. Alter the switch-off speed of the Audi parking System [Select] [10 - Park/Steer Assist] [Adaptation - 10] Select Channel 23 and Read Change the value from 10 to 20 (Max speed in Km/h - 20 is the highest you can set it to) Press Test then press Save 25. Disable/memorize/invert Start & Stop [Select] [09-Cent. Elect.] [Security Access - 16] (enter security code - 20113) [Adaptation - 10] Select Channel 34 and Read if you subtract 4 from the original value --> Start&Stop always disabled if you add 32 to the original value --> memorize last status (the Start & Stop status at engine startup will be the one at last engine shutdown) if you add 64 to the original value --> Start & Stop button light will be reversed: off if Start & Stop is disabled, and on if Start & Stop is enabled. Press Test then press Save 26. Activation of footwell lighting for vehicles without Lighting Pack / Ambient Lighting This allows you to use the MMI to set the footwell lighting level while driving. Tested on cars with MMI 3G+ (Tech pack). [Select] [09-Cent. Elect] [Coding - 07] [Long Coding Helper] Click on byte 16 and enable bit 6 [Do It!] Enter the Hidden Menu as in step 5 above. Select Car Select Cardevicelist Check "Interior Light" Return Select Carmenuoperation Set "Interior Light" from 0 to 5 Return Press CAR to exit the hidden menu Reboot the MMI Po Liftingu ========================= 1. Włączenie Testu ZegarówThis will sweep the needles of the speedo and rev counter through their full range automatically when you start the engine. [Select] [17 - Instruments] [Coding - 07] [Long Coding Helper] Click on byte 1 and you'll see the selectable option: "Gauge Test/Needle Sweep active" Check this option [Do It!] This produced expected results 2. Włączenie Lap Timer'aThis adds an extra selectable screen in the DIS that displays lap timers, turbo boost and oil temperature. For cars with HUD it also shows a different HUD. [Select] [17 - Instruments] [Coding - 07] [Long Coding Helper] Click on byte 1 and you'll see the selectable option: "Lap Timer active" Check this option [Do It!] This produced expected results 3. Doświetlenie KrawężnikówIlluminating the kerb when turning hard left or right at low speeds with dipped beam on, by turning on the all-weather light on the relevant side of the car. This also works with Matrix LED lights. [Select] [09-Cent. Elect.] [Coding - 07] [Long Coding Helper] Click on byte 4 and enable bit 0 [Do It!] This produced expected results 4. Sygnał Zamknięcia ZamkaChirp the alarm siren briefly when the alarm activates (ie all doors are closed and the car is locked) [Select] [46-Central Conv.] [Coding - 07] [Long Coding Helper] Click on byte 1 and in bit 2 you'll see the selectable option: "Anti-Theft-System: Horn Confirmation active" Check this option [Do It!] This produced expected results 8. Aktywacja opuszczania prawego lusterka przy jeździe na wstecznym bieguWhen reverse gear is selected, the passenger door mirror dips to show the kerb if the mirror control knob is set to the passenger door mirror position. When driving forwards and exceeding 5mph or when switching off the car, the passenger mirror returns to its original position. If the position of the mirror is changed when dipped, this change is remembered the next time the mirror dips. This is enabled as standard on cars with electric memory seats but can be enabled using VCDS on cars that don't. [Select] [52 - Door Elect, Pass] [Coding - 07] [Long Coding Helper] Click on Byte 4 (5th one along from the left) ...
djlonger007